Neko da radi bearing edgove?

Palice, opne, metlice...

Moderator: Supermoderatori

User avatar
markus
Dobošar
Dobošar
Posts: 62
Joined: January 24th, 2008, 3:23 pm
Moj Bubanj: Slingerland 24 13 16
Location: Beograd

Neko da radi bearing edgove?

Post by markus » May 13th, 2011, 12:44 am

Zanima me, a verovatno i ostale forumase, da li ima neko ko radi nove ivice na bubnjevima?

Mene licno interesuje Beograd i okolina, ali nek tema bude sa sve krajeve....

Naravski i cena, ako se zna, bilo bi sjajno.... Bar okvirno!
User avatar
markus
Dobošar
Dobošar
Posts: 62
Joined: January 24th, 2008, 3:23 pm
Moj Bubanj: Slingerland 24 13 16
Location: Beograd

Re: Neko da radi bearing edgove?

Post by markus » May 28th, 2011, 2:27 am

Mislim da sam nasao potencijalnog lika za ovaj posao...
Kad budem znao detalje i da li je to to javljam, naravno ako ikoga zanima
uopste???
User avatar
Mare
Bubnjar!
Bubnjar!
Posts: 764
Joined: January 13th, 2008, 10:51 am
Location: Austrija
Contact:

Re: Neko da radi bearing edgove?

Post by Mare » May 28th, 2011, 3:46 am

Možeš to i sam da uradiš ako imaš strpljenja i ako si pažljiv. Naravno za alat će ti biti potrebno negde oko ~60€.
Ja nisam bubnjar, ja sam činelista
Dok ne probam lava, za mene je svinja kralj životinja
Svi instrumenti imaju dušu, samo bubanj ima muda
User avatar
Woody
Virtuoz!
Virtuoz!
Posts: 1370
Joined: October 14th, 2010, 1:07 pm
Moj Bubanj: Mapex, Pearl, Ludwig, Paiste, Anatolian, Roland
Moji bendovi: Dancing Waves, freelance
Inspiracija: Bonham, McBrain, Kache, Bordin, Collins, Copeland, Garo...
Location: Beograd, highseas

Re: Neko da radi bearing edgove?

Post by Woody » May 31st, 2011, 2:05 pm

Samo ti okaci kontakt i neke reference, nece da se baci :thumbup:
The Sea, The Sea
User avatar
Goatbeard
Virtuoz!
Virtuoz!
Posts: 1086
Joined: April 26th, 2009, 12:04 am
Inspiracija: Tony Checkers & many more

Re: Neko da radi bearing edgove?

Post by Goatbeard » October 8th, 2013, 10:45 am

Ništa novo na ovu temu?
Mare wrote:Možeš to i sam da uradiš ako imaš strpljenja i ako si pažljiv. Naravno za alat će ti biti potrebno negde oko ~60€.
Šta konkretno predlažeš ?
.--. --- - .--. .. ...
User avatar
CEDAPNM
Redovno vežba
Redovno vežba
Posts: 533
Joined: January 1st, 2010, 7:59 pm
Location: Svilajnac

Re: Neko da radi bearing edgove?

Post by CEDAPNM » October 8th, 2013, 4:48 pm

Ja sam to radio rucno, ali za to ce ti trebati nekih 7-8 sati, ako radis samo turpijom i smirglom, a ako imas frezer (table router) onda ce ti trebati nekih 15 minuta lol
We'll show no mercy, we'll kill them all!!!!
User avatar
Goatbeard
Virtuoz!
Virtuoz!
Posts: 1086
Joined: April 26th, 2009, 12:04 am
Inspiracija: Tony Checkers & many more

Re: Neko da radi bearing edgove?

Post by Goatbeard » October 8th, 2013, 5:45 pm

To sa šmirglom sam radio (neka sitna intervencija) ali problem su različiti uglovi na unutarnjoj i spoljnoj kosini tj. rezanje istih iznova. To ne bih sam čačkao a gde sam pitao ili nemaju dobru mašinu ili su bez iskustva. Hteo sam prepravku obe ivice sa novim specifikacijama i ne bih da ga upropastim iako je jeftinija klasa i imam bolji set - to mi je prvi bubanj koji sam kupio. Jbg,emocije... ;)
.--. --- - .--. .. ...
User avatar
CEDAPNM
Redovno vežba
Redovno vežba
Posts: 533
Joined: January 1st, 2010, 7:59 pm
Location: Svilajnac

Re: Neko da radi bearing edgove?

Post by CEDAPNM » October 8th, 2013, 6:27 pm

ja sam to ovako radio, sve moras precizno da obelezis, i da budes jako pazljiv kad radis to, da stalno proveravas i da ne brzas :)
You do not have the required permissions to view the files attached to this post.
We'll show no mercy, we'll kill them all!!!!
User avatar
downbeat
Virtuoz!
Virtuoz!
Posts: 2181
Joined: March 1st, 2008, 1:26 pm
Moj Bubanj: Manic Drum, Istanbul Cymbals
Location: Banja Luka

Re: Neko da radi bearing edgove?

Post by downbeat » October 8th, 2013, 6:30 pm

Ja to ne bih ručno radio.
User avatar
Goatbeard
Virtuoz!
Virtuoz!
Posts: 1086
Joined: April 26th, 2009, 12:04 am
Inspiracija: Tony Checkers & many more

Re: Neko da radi bearing edgove?

Post by Goatbeard » October 8th, 2013, 10:49 pm

Mašine su ipak pouzdanija varijanta,naročito kod rezanja profila.Zato i osvežavamo temu jer će možda natrčati neko sa kontaktom 'mašiniste'. :D

@ CEDAPNM - Ti si radio sa frezerom ili nekom drugom mašinom? Ne vidim na fotki na koliko si stepeni sekao ivicu?
.--. --- - .--. .. ...
User avatar
downbeat
Virtuoz!
Virtuoz!
Posts: 2181
Joined: March 1st, 2008, 1:26 pm
Moj Bubanj: Manic Drum, Istanbul Cymbals
Location: Banja Luka

Re: Neko da radi bearing edgove?

Post by downbeat » October 9th, 2013, 12:15 am

Ja znam jedne koji to rade, ali su u Sloveniji. :)
User avatar
Goatbeard
Virtuoz!
Virtuoz!
Posts: 1086
Joined: April 26th, 2009, 12:04 am
Inspiracija: Tony Checkers & many more

Re: Neko da radi bearing edgove?

Post by Goatbeard » October 9th, 2013, 12:37 am

Hahaaa,video sam na njihovom sajtu,čak je i cena pristojna. Samo,oni su EU a mi Nesvrstani = mnogo zavrzlama oko papira i još više šuške! :zid:
.--. --- - .--. .. ...
User avatar
CEDAPNM
Redovno vežba
Redovno vežba
Posts: 533
Joined: January 1st, 2010, 7:59 pm
Location: Svilajnac

Re: Neko da radi bearing edgove?

Post by CEDAPNM » October 9th, 2013, 1:47 pm

ja sam rucno radio, ali sad sam u fazi pravljenja postolja za frezer pa cu raditi frezerom :) a ovo sto sam radio do sad je sve na 45stepeni :)
We'll show no mercy, we'll kill them all!!!!
User avatar
downbeat
Virtuoz!
Virtuoz!
Posts: 2181
Joined: March 1st, 2008, 1:26 pm
Moj Bubanj: Manic Drum, Istanbul Cymbals
Location: Banja Luka

Re: Neko da radi bearing edgove?

Post by downbeat » October 9th, 2013, 6:01 pm

Goatbeard wrote:Hahaaa,video sam na njihovom sajtu,čak je i cena pristojna. Samo,oni su EU a mi Nesvrstani = mnogo zavrzlama oko papira i još više šuške! :zid:
:)
User avatar
DjoleObr
Redovno vežba
Redovno vežba
Posts: 370
Joined: August 23rd, 2010, 11:54 pm
Moj Bubanj: Premier APK, Paiste, Zildjian, Symrna, Stagg
Moji bendovi: U Zmajevom Gnezdu, Oslobodioci
Inspiracija: Kerim,Lopez,Harrison
Location: Obrenovac

Re: Neko da radi bearing edgove?

Post by DjoleObr » October 29th, 2013, 4:51 pm

Zanima me da li se isplati raditi ivice na Premier APk-u. Pre neki dan kad sam stimovao bubanj i cistio sve video sam da su mu ivice gotovo ravne. AKo uradim ivice hocu li dobiti bolji zvuk ili cu samo unistiti i spustiti mu cenu jos vise. Naravno dao bih nekom ko zna to da radi a ne sam :)

pozdrav

Code: Select all

https://www.youtube.com/user/DjoleObr/videos
Post Reply